Convert Amperes/Volt to Kilosiemens
Ampere/Volt (A/V) to Kilosiemens (kS) electric conductance conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 A/V = 0.001 kS
1 Ampere/Volt = 0.001 Kilosiemens
1 Kilosiemens = 1000 Amperes/Volt
1 A/V in every supported unit
Conversion chart: Ampere/Volt to Kilosiemens
Conversion table
| Ampere/Volt (A/V) | Kilosiemens (kS) |
|---|---|
| 0.01 A/V | 1E-05 kS |
| 0.1 A/V | 0.0001 kS |
| 1 A/V | 0.001 kS |
| 2 A/V | 0.002 kS |
| 3 A/V | 0.003 kS |
| 5 A/V | 0.005 kS |
| 10 A/V | 0.01 kS |
| 20 A/V | 0.02 kS |
| 50 A/V | 0.05 kS |
| 100 A/V | 0.1 kS |
| 1000 A/V | 1 kS |
Ampere/Volt (A/V)
Definition: The literal defining ratio behind the siemens: one ampere of current per volt of applied potential difference. Writing conductance this way spells out the underlying physical relationship (current divided by voltage) instead of using the named derived unit.
History: This form predates the eponymous "siemens" name; early electrical engineers and physicists described conductance directly in terms of the base SI units ampere and volt before the derived unit was formally named and standardized in 1935 and adopted into the SI in 1971.
Current use: Still used in textbooks and derivations to make explicit that conductance is current per unit voltage, and it converts to siemens with a factor of exactly 1 since the two are, by definition, the same quantity.
Kilosiemens (kS)
Definition: One thousand siemens, an SI-prefixed multiple for conductance values larger than a single siemens but not so large as to warrant the mega- prefix.
History: The kilo- prefix dates to the original 1795 French metric system and was carried forward unchanged into the modern SI; it was attached to the siemens as a matter of course once the unit itself was formally adopted in 1971.
Current use: Used in power-electronics and grid-equipment specifications where the conductance of busbars, large capacitor banks, or low-resistance shunts is more conveniently expressed in the thousands than in raw siemens.
Supported Units
| Unit | Symbol | In Siemens |
|---|---|---|
| Siemens | S | 1 S |
| Megasiemens | MS | 1000000 S |
| Kilosiemens | kS | 1000 S |
| Millisiemens | mS | 0.001 S |
| Microsiemens | µS | 1E-06 S |
| Ampere/Volt | A/V | 1 S |
| Mho | ℧ | 1 S |
| Gemmho | gemmho | 1E-06 S |
| Micromho | µmho | 1E-06 S |
| Abmho | abmho | 1E+09 S |
| Statmho | statmho | 1.11235E-12 S |
| Quantized Hall Conductance | e²/h | 3.87405E-05 S |
About These Parameters
- Value
- The conductance value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a picosiemens-level insulator leakage figure to a gigasiemens-scale superconductor measurement.
- From Unit
- The unit your input value is currently measured in — a modern component datasheet's siemens (S) rating, or a legacy figure quoted in mho, abmho, or statmho.
- To Unit
- The unit you want the result converted into. Use the swap button to flip From and To instantly, which is handy when translating an older mho-based figure into the modern siemens or vice versa.
How Electric Conductance Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the siemens. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Ampere/Volt → Kilosiemens: multiply by 0.001. For example, 1 A/V × 0.001 = 0.001 kS.
Conductance Is the Reciprocal of Resistance
Conductance and resistance describe the same physical relationship between voltage and current from opposite directions: resistance (ohms) measures how strongly a component opposes current flow, while conductance (siemens) measures how readily it allows current through. Because they are exact reciprocals (G = 1/R), a very good conductor — a thick copper busbar, for example — has a tiny resistance and a correspondingly large conductance, while a good insulator has a huge resistance and a conductance so small it is usually expressed in picosiemens or smaller. This reciprocal relationship is also why conductances of components wired in parallel simply add together, while their resistances do not.
From Mho to Siemens
Before 1971, the unit of conductance had no single settled name: engineers commonly called it the "mho" — "ohm" spelled backwards, with an upside-down omega (℧) as its symbol — to emphasize that it was resistance's reciprocal. The International Electrotechnical Commission formally adopted "siemens," named for Ernst Werner von Siemens, in 1935, and the unit was folded into the International System of Units in 1971, gradually displacing "mho" in textbooks, standards, and datasheets over the following decades. The two units remain numerically identical (1 mho = 1 S), so older equipment and literature that still uses "mho" converts to the modern siemens with a factor of exactly 1.
Example
A conductance of 1 A/V equals 0.001 kS. For scale, a typical incandescent light bulb filament has a conductance around 0.08 siemens (roughly 12 ohms of resistance), a thick copper ground strap can exceed several thousand siemens, and a high-quality electrical insulator's leakage conductance is often measured in picosiemens or smaller.
Frequently Asked Questions
How many Kilosiemens are in 1 Ampere/Volt?
1 Ampere/Volt (A/V) equals exactly 0.001 Kilosiemens (kS).
What is the difference between conductance and conductivity?
Conductance (siemens) describes a specific object or component's ability to conduct current — it depends on that object's size, shape, and material. Conductivity (siemens per meter) is a material property that strips out size and shape, describing how well a material conducts current per unit length regardless of the particular sample. Use this converter for whole-component conductance; use the companion Electric Conductivity Converter for the size-independent material property.
Is mho the same as siemens?
Yes — mho and siemens are numerically identical (1 mho = 1 S). "Mho" was the informal, widely used name for the unit before the International Electrotechnical Commission standardized "siemens" in 1935, and it still appears in older equipment, textbooks, and some U.S. water-quality literature.
Why is the quantized Hall conductance such a small, oddly specific number?
The quantized Hall conductance (e²/h ≈ 3.87405 × 10⁻⁵ S) is a fundamental physical constant, not a rounded engineering unit — it's built from the elementary charge (e) and the Planck constant (h). Discovered by Klaus von Klitzing in 1980, it's the exact step size by which conductance jumps in the quantum Hall effect, and because it depends only on fundamental constants, it's used today as a precision reference for realizing the ohm and siemens in metrology labs.
What are abmho and statmho used for today?
Abmho (from the CGS-EMU system) and statmho (from the CGS-ESU system) are both 19th-century units of conductance that predate the SI. They're rarely used in modern engineering, but still appear occasionally in historical physics literature and in theoretical work that frames electromagnetic calculations natively in CGS units rather than SI.