CalculatorBoom

Convert Nanohenries to Webers/Ampere

Nanohenry (nH) to Weber/Ampere (Wb/A) inductance conversion — enter any value below to get an instant result, or use the table for common values.

Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.

The numeric value you want to convert. Decimals are accepted.

Result

1 Nanohenry = 1E-09 Webers/Ampere

1 Weber/Ampere = 1E+09 Nanohenries

1 nH in every supported unit

Conversion chart: Nanohenry to Webers/Ampere

Conversion table

Nanohenry (nH) Weber/Ampere (Wb/A)
0.01 nH 1E-11 Wb/A
0.1 nH 1E-10 Wb/A
1 nH 1E-09 Wb/A
2 nH 2E-09 Wb/A
3 nH 3E-09 Wb/A
5 nH 5E-09 Wb/A
10 nH 1E-08 Wb/A
20 nH 2E-08 Wb/A
50 nH 5E-08 Wb/A
100 nH 1E-07 Wb/A
1000 nH 1E-06 Wb/A

Nanohenry (nH)

Definition: One billionth of a henry (1 nH = 0.000000001 H), used for the very small inductances found in high-frequency and high-speed digital circuits.

History: It became practically relevant as radio-frequency and microwave engineering, and later high-speed digital signal-integrity work, needed to quantify inductance well below the microhenry scale, including parasitic inductance from wires and leads.

Current use: The typical unit for specifying bond-wire inductance in integrated-circuit packaging, PCB trace inductance, and small RF-tuning inductors used in gigahertz-range wireless circuits.

Weber/Ampere (Wb/A)

Definition: The literal definitional ratio behind the henry — one henry is, by definition, exactly one weber of magnetic flux linkage per ampere of current, so weber/ampere is mathematically identical to the henry.

History: This expression follows directly from the flux-linkage definition of inductance (L = Φ/I), formalized when the henry was adopted as an SI derived unit expressed in terms of the weber (magnetic flux) and ampere, both already defined SI units.

Current use: Used in physics and electrical engineering derivations when it is clearer to express inductance through its underlying flux-linkage relationship rather than the named henry unit, particularly in magnetic circuit and transformer analysis.

Supported Units

Unit Symbol In Henry
Henry H 1 H
Kilohenry kH 1000 H
Millihenry mH 0.001 H
Microhenry µH 1E-06 H
Nanohenry nH 1E-09 H
Picohenry pH 1E-12 H
Femtohenry fH 1E-15 H
Abhenry abH 1E-09 H
Stathenry statH 8.98755E+11 H
Weber/Ampere Wb/A 1 H

About These Parameters

Value
The inductance value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a tiny nanohenry PCB-trace parasitic to a large power-transformer winding's multi-henry rating.
From Unit
The unit your input value is currently measured in — an inductor datasheet's millihenry or microhenry rating, or a historical figure quoted in abhenries or stathenries from the older CGS unit systems.
To Unit
The unit you want the result converted into. Use the swap button to flip From and To instantly, handy when translating a datasheet value into a different SI-prefixed scale or back to the base henry.

How Inductance Conversion Works

The Formula

Every unit here is defined by a fixed multiplier relative to the henry. To convert a value from one unit to another:

result = value × (factor of "From" unit ÷ factor of "To" unit)

For Nanohenry → Weber/Ampere: multiply by 1E-09. For example, 1 nH × 1E-09 = 1E-09 Wb/A.

Why Inductors Span Such a Wide Range of Units

A henry is a relatively large amount of inductance for a physical coil to produce — winding enough turns around a large enough core to reach a full henry generally means a bulky component, the kind found in mains-frequency power transformers and large chokes. Most inductors used in switching power supplies, RF circuits, and signal filtering only need a fraction of a henry to do their job, which is why millihenries and microhenries are the everyday scale for real components. At the other extreme, any wire, PCB trace, or connector lead has some small amount of unavoidable "parasitic" inductance — usually measured in nanohenries or picohenries — that becomes significant only at the high frequencies and fast switching speeds used in modern digital and RF electronics.

SI Henries vs. CGS Abhenries and Stathenries

Before the SI system unified electrical units around the henry, volt, and ampere, 19th-century physicists worked in the centimeter-gram-second (CGS) system, which split into two competing branches: the electromagnetic (emu) branch, whose inductance unit is the abhenry (equal to a tiny one billionth of a henry), and the electrostatic (esu) branch, whose unit is the stathenry (equal to a massive 898.8 billion henries). That enormous gap — the mirror image of the abfarad/statfarad relationship in capacitance — comes from the same speed-of-light-squared relationship that links the esu and emu systems throughout classical electromagnetism. Modern electronics almost never uses either CGS unit directly, but they still turn up when translating older theoretical physics texts into today's henry-based units.

Example

An inductance of 1 nH equals 1E-09 Wb/A. For scale, a small RF inductor on a circuit board might be rated around 10 microhenries, a typical switching power-supply inductor might be a few hundred microhenries to a few millihenries, and a large mains-frequency power transformer winding can reach several henries.

Frequently Asked Questions

How many Webers/Ampere are in 1 Nanohenry?

1 Nanohenry (nH) equals exactly 1E-09 Webers/Ampere (Wb/A).

Why are inductors almost never rated in whole henries?

A henry is a relatively large amount of inductance to build into a small, practical coil — reaching a full henry typically requires a bulky winding around a large magnetic core, the kind used in mains-frequency transformers. Everyday inductors in power supplies, RF circuits, and filters only need a fraction of a henry, so they're rated in millihenries or microhenries instead.

Is weber/ampere the same thing as a henry?

Yes — they're mathematically identical. The henry is defined as exactly one weber of magnetic flux linkage per ampere of current (1 H = 1 Wb/A), so expressing an inductance in webers per ampere gives the exact same numeric value as expressing it in henries.

Why is the stathenry so much larger than the abhenry?

Both come from the older centimeter-gram-second (CGS) system, but from opposite branches: the abhenry is a CGS electromagnetic (emu) unit, while the stathenry is a CGS electrostatic (esu) unit. The two branches are related by the speed of light squared, which is why the abhenry (10⁻⁹ henries) and stathenry (about 8.9876 × 10¹¹ henries) sit roughly 21 orders of magnitude apart despite both measuring inductance.

What's a typical inductance value for common electronics?

It depends heavily on the application: RF and high-frequency tuning circuits often use nanohenry to microhenry inductors, switching power-supply inductors commonly range from a few microhenries to a few millihenries, and large mains-frequency transformer or motor windings can reach several henries. Kilohenry-scale inductance is essentially never seen outside specialized grid equipment.

Convert Nanohenry to Other Inductance Units

Possible Inductance Conversions

Stathenry to Nanohenries Weber/Ampere to Picohenries Picohenry to Abhenries Henry to Abhenries Stathenry to Webers/Ampere Abhenry to Henries Microhenry to Stathenries Henry to Picohenries Stathenry to Abhenries Henry to Nanohenries Femtohenry to Kilohenries Picohenry to Millihenries Weber/Ampere to Stathenries Nanohenry to Henries Stathenry to Henries Microhenry to Femtohenries Henry to Microhenries Nanohenry to Picohenries Femtohenry to Abhenries Microhenry to Nanohenries Weber/Ampere to Millihenries Kilohenry to Picohenries Millihenry to Abhenries Stathenry to Microhenries Microhenry to Millihenries Abhenry to Kilohenries Kilohenry to Nanohenries Picohenry to Stathenries Picohenry to Kilohenries Abhenry to Femtohenries Kilohenry to Henries Millihenry to Femtohenries Henry to Webers/Ampere Microhenry to Picohenries Millihenry to Stathenries Henry to Kilohenries Henry to Femtohenries Femtohenry to Stathenries Weber/Ampere to Nanohenries Henry to Stathenries Millihenry to Picohenries Nanohenry to Femtohenries Nanohenry to Webers/Ampere Microhenry to Kilohenries Nanohenry to Abhenries Femtohenry to Microhenries Kilohenry to Abhenries Millihenry to Microhenries Kilohenry to Femtohenries Femtohenry to Millihenries Millihenry to Nanohenries Stathenry to Picohenries Picohenry to Femtohenries Microhenry to Henries Femtohenry to Nanohenries Kilohenry to Webers/Ampere Kilohenry to Stathenries Abhenry to Microhenries Abhenry to Millihenries Picohenry to Microhenries Henry to Millihenries Nanohenry to Kilohenries Femtohenry to Webers/Ampere Microhenry to Webers/Ampere Picohenry to Nanohenries Millihenry to Kilohenries Nanohenry to Stathenries Femtohenry to Henries Abhenry to Picohenries Abhenry to Stathenries Femtohenry to Picohenries Picohenry to Henries Weber/Ampere to Kilohenries Kilohenry to Microhenries Millihenry to Henries Weber/Ampere to Abhenries Stathenry to Femtohenries Stathenry to Millihenries Picohenry to Webers/Ampere Nanohenry to Millihenries Nanohenry to Microhenries Weber/Ampere to Henries Microhenry to Abhenries Stathenry to Kilohenries Abhenry to Webers/Ampere Kilohenry to Millihenries Abhenry to Nanohenries Weber/Ampere to Microhenries Weber/Ampere to Femtohenries Millihenry to Webers/Ampere

See also