CalculatorBoom

Convert Microhenries to Millihenries

Microhenry (µH) to Millihenry (mH) inductance conversion — enter any value below to get an instant result, or use the table for common values.

Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.

The numeric value you want to convert. Decimals are accepted.

Result

1 Microhenry = 0.001 Millihenries

1 Millihenry = 1000 Microhenries

1 µH in every supported unit

Conversion chart: Microhenry to Millihenries

Conversion table

Microhenry (µH) Millihenry (mH)
0.01 µH 1E-05 mH
0.1 µH 0.0001 mH
1 µH 0.001 mH
2 µH 0.002 mH
3 µH 0.003 mH
5 µH 0.005 mH
10 µH 0.01 mH
20 µH 0.02 mH
50 µH 0.05 mH
100 µH 0.1 mH
1000 µH 1 mH

Microhenry (µH)

Definition: One millionth of a henry (1 µH = 0.000001 H), the standard scale for small signal and RF inductors.

History: It was introduced as radio and high-frequency circuit design required inductance values far below a millihenry, following the same SI "micro-" prefix used across other electrical units.

Current use: Widely used for RF chokes, antenna coils, and the small inductors found in switching power supplies and wireless communication circuits, where even a PCB trace or wire loop can contribute a measurable fraction of a microhenry.

Millihenry (mH)

Definition: One thousandth of a henry (1 mH = 0.001 H) — one of the most commonly used inductance units in practical circuit design.

History: Derived from the SI "milli-" prefix, it came into everyday use as inductor manufacturing matured and typical coil and transformer values settled into the fractional-henry range.

Current use: The standard rating for power-supply chokes, switching-regulator inductors, motor windings, and audio crossover inductors — a typical DC-DC converter inductor might be rated between 1 and 100 millihenries.

Supported Units

Unit Symbol In Henry
Henry H 1 H
Kilohenry kH 1000 H
Millihenry mH 0.001 H
Microhenry µH 1E-06 H
Nanohenry nH 1E-09 H
Picohenry pH 1E-12 H
Femtohenry fH 1E-15 H
Abhenry abH 1E-09 H
Stathenry statH 8.98755E+11 H
Weber/Ampere Wb/A 1 H

About These Parameters

Value
The inductance value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a tiny nanohenry PCB-trace parasitic to a large power-transformer winding's multi-henry rating.
From Unit
The unit your input value is currently measured in — an inductor datasheet's millihenry or microhenry rating, or a historical figure quoted in abhenries or stathenries from the older CGS unit systems.
To Unit
The unit you want the result converted into. Use the swap button to flip From and To instantly, handy when translating a datasheet value into a different SI-prefixed scale or back to the base henry.

How Inductance Conversion Works

The Formula

Every unit here is defined by a fixed multiplier relative to the henry. To convert a value from one unit to another:

result = value × (factor of "From" unit ÷ factor of "To" unit)

For Microhenry → Millihenry: multiply by 0.001. For example, 1 µH × 0.001 = 0.001 mH.

Why Inductors Span Such a Wide Range of Units

A henry is a relatively large amount of inductance for a physical coil to produce — winding enough turns around a large enough core to reach a full henry generally means a bulky component, the kind found in mains-frequency power transformers and large chokes. Most inductors used in switching power supplies, RF circuits, and signal filtering only need a fraction of a henry to do their job, which is why millihenries and microhenries are the everyday scale for real components. At the other extreme, any wire, PCB trace, or connector lead has some small amount of unavoidable "parasitic" inductance — usually measured in nanohenries or picohenries — that becomes significant only at the high frequencies and fast switching speeds used in modern digital and RF electronics.

SI Henries vs. CGS Abhenries and Stathenries

Before the SI system unified electrical units around the henry, volt, and ampere, 19th-century physicists worked in the centimeter-gram-second (CGS) system, which split into two competing branches: the electromagnetic (emu) branch, whose inductance unit is the abhenry (equal to a tiny one billionth of a henry), and the electrostatic (esu) branch, whose unit is the stathenry (equal to a massive 898.8 billion henries). That enormous gap — the mirror image of the abfarad/statfarad relationship in capacitance — comes from the same speed-of-light-squared relationship that links the esu and emu systems throughout classical electromagnetism. Modern electronics almost never uses either CGS unit directly, but they still turn up when translating older theoretical physics texts into today's henry-based units.

Example

An inductance of 1 µH equals 0.001 mH. For scale, a small RF inductor on a circuit board might be rated around 10 microhenries, a typical switching power-supply inductor might be a few hundred microhenries to a few millihenries, and a large mains-frequency power transformer winding can reach several henries.

Frequently Asked Questions

How many Millihenries are in 1 Microhenry?

1 Microhenry (µH) equals exactly 0.001 Millihenries (mH).

Why are inductors almost never rated in whole henries?

A henry is a relatively large amount of inductance to build into a small, practical coil — reaching a full henry typically requires a bulky winding around a large magnetic core, the kind used in mains-frequency transformers. Everyday inductors in power supplies, RF circuits, and filters only need a fraction of a henry, so they're rated in millihenries or microhenries instead.

Is weber/ampere the same thing as a henry?

Yes — they're mathematically identical. The henry is defined as exactly one weber of magnetic flux linkage per ampere of current (1 H = 1 Wb/A), so expressing an inductance in webers per ampere gives the exact same numeric value as expressing it in henries.

Why is the stathenry so much larger than the abhenry?

Both come from the older centimeter-gram-second (CGS) system, but from opposite branches: the abhenry is a CGS electromagnetic (emu) unit, while the stathenry is a CGS electrostatic (esu) unit. The two branches are related by the speed of light squared, which is why the abhenry (10⁻⁹ henries) and stathenry (about 8.9876 × 10¹¹ henries) sit roughly 21 orders of magnitude apart despite both measuring inductance.

What's a typical inductance value for common electronics?

It depends heavily on the application: RF and high-frequency tuning circuits often use nanohenry to microhenry inductors, switching power-supply inductors commonly range from a few microhenries to a few millihenries, and large mains-frequency transformer or motor windings can reach several henries. Kilohenry-scale inductance is essentially never seen outside specialized grid equipment.

Convert Microhenry to Other Inductance Units

Possible Inductance Conversions

Abhenry to Stathenries Abhenry to Femtohenries Millihenry to Kilohenries Stathenry to Microhenries Femtohenry to Henries Femtohenry to Nanohenries Stathenry to Femtohenries Picohenry to Kilohenries Millihenry to Stathenries Microhenry to Webers/Ampere Abhenry to Millihenries Nanohenry to Millihenries Microhenry to Kilohenries Microhenry to Henries Kilohenry to Picohenries Henry to Nanohenries Kilohenry to Stathenries Nanohenry to Webers/Ampere Nanohenry to Henries Femtohenry to Kilohenries Millihenry to Nanohenries Kilohenry to Microhenries Weber/Ampere to Picohenries Stathenry to Millihenries Femtohenry to Microhenries Stathenry to Webers/Ampere Henry to Picohenries Nanohenry to Picohenries Weber/Ampere to Millihenries Microhenry to Femtohenries Weber/Ampere to Nanohenries Nanohenry to Kilohenries Weber/Ampere to Abhenries Stathenry to Nanohenries Femtohenry to Picohenries Kilohenry to Henries Millihenry to Microhenries Nanohenry to Microhenries Kilohenry to Nanohenries Microhenry to Stathenries Nanohenry to Abhenries Picohenry to Stathenries Weber/Ampere to Stathenries Abhenry to Picohenries Picohenry to Abhenries Millihenry to Abhenries Picohenry to Nanohenries Abhenry to Kilohenries Henry to Millihenries Nanohenry to Stathenries Henry to Stathenries Weber/Ampere to Femtohenries Femtohenry to Abhenries Henry to Microhenries Abhenry to Microhenries Femtohenry to Webers/Ampere Picohenry to Millihenries Millihenry to Henries Millihenry to Webers/Ampere Millihenry to Picohenries Abhenry to Nanohenries Weber/Ampere to Henries Abhenry to Webers/Ampere Henry to Kilohenries Microhenry to Picohenries Henry to Abhenries Stathenry to Kilohenries Weber/Ampere to Microhenries Kilohenry to Webers/Ampere Stathenry to Abhenries Henry to Webers/Ampere Microhenry to Abhenries Microhenry to Millihenries Picohenry to Webers/Ampere Kilohenry to Millihenries Stathenry to Picohenries Kilohenry to Femtohenries Abhenry to Henries Kilohenry to Abhenries Weber/Ampere to Kilohenries Picohenry to Femtohenries Microhenry to Nanohenries Henry to Femtohenries Millihenry to Femtohenries Femtohenry to Stathenries Picohenry to Microhenries Femtohenry to Millihenries Stathenry to Henries Nanohenry to Femtohenries Picohenry to Henries

See also