CalculatorBoom

Convert Nanohenries to Stathenries

Nanohenry (nH) to Stathenry (statH) inductance conversion — enter any value below to get an instant result, or use the table for common values.

Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.

The numeric value you want to convert. Decimals are accepted.

Result

1 Nanohenry = 1.11265E-21 Stathenries

1 Stathenry = 8.98755E+20 Nanohenries

1 nH in every supported unit

Conversion chart: Nanohenry to Stathenries

Conversion table

Nanohenry (nH) Stathenry (statH)
0.01 nH 1.11265E-23 statH
0.1 nH 1.11265E-22 statH
1 nH 1.11265E-21 statH
2 nH 2.2253E-21 statH
3 nH 3.33795E-21 statH
5 nH 5.56325E-21 statH
10 nH 1.11265E-20 statH
20 nH 2.2253E-20 statH
50 nH 5.56325E-20 statH
100 nH 1.11265E-19 statH
1000 nH 1.11265E-18 statH

Nanohenry (nH)

Definition: One billionth of a henry (1 nH = 0.000000001 H), used for the very small inductances found in high-frequency and high-speed digital circuits.

History: It became practically relevant as radio-frequency and microwave engineering, and later high-speed digital signal-integrity work, needed to quantify inductance well below the microhenry scale, including parasitic inductance from wires and leads.

Current use: The typical unit for specifying bond-wire inductance in integrated-circuit packaging, PCB trace inductance, and small RF-tuning inductors used in gigahertz-range wireless circuits.

Stathenry (statH)

Definition: The unit of inductance in the CGS electrostatic (esu) system — an enormous value equal to roughly 898.8 billion henries, arising from defining inductance through the electrostatic branch of CGS units.

History: It was derived alongside the statfarad from the electrostatic CGS system, with its huge numeric factor relative to the henry stemming from the same speed-of-light-squared relationship that links the esu and emu unit systems throughout classical electromagnetism.

Current use: Almost never used in applied engineering due to its impractically large scale relative to real inductors; it survives only in theoretical physics work that stays consistently within the Gaussian esu unit system.

Supported Units

Unit Symbol In Henry
Henry H 1 H
Kilohenry kH 1000 H
Millihenry mH 0.001 H
Microhenry µH 1E-06 H
Nanohenry nH 1E-09 H
Picohenry pH 1E-12 H
Femtohenry fH 1E-15 H
Abhenry abH 1E-09 H
Stathenry statH 8.98755E+11 H
Weber/Ampere Wb/A 1 H

About These Parameters

Value
The inductance value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a tiny nanohenry PCB-trace parasitic to a large power-transformer winding's multi-henry rating.
From Unit
The unit your input value is currently measured in — an inductor datasheet's millihenry or microhenry rating, or a historical figure quoted in abhenries or stathenries from the older CGS unit systems.
To Unit
The unit you want the result converted into. Use the swap button to flip From and To instantly, handy when translating a datasheet value into a different SI-prefixed scale or back to the base henry.

How Inductance Conversion Works

The Formula

Every unit here is defined by a fixed multiplier relative to the henry. To convert a value from one unit to another:

result = value × (factor of "From" unit ÷ factor of "To" unit)

For Nanohenry → Stathenry: multiply by 1.11265E-21. For example, 1 nH × 1.11265E-21 = 1.11265E-21 statH.

Why Inductors Span Such a Wide Range of Units

A henry is a relatively large amount of inductance for a physical coil to produce — winding enough turns around a large enough core to reach a full henry generally means a bulky component, the kind found in mains-frequency power transformers and large chokes. Most inductors used in switching power supplies, RF circuits, and signal filtering only need a fraction of a henry to do their job, which is why millihenries and microhenries are the everyday scale for real components. At the other extreme, any wire, PCB trace, or connector lead has some small amount of unavoidable "parasitic" inductance — usually measured in nanohenries or picohenries — that becomes significant only at the high frequencies and fast switching speeds used in modern digital and RF electronics.

SI Henries vs. CGS Abhenries and Stathenries

Before the SI system unified electrical units around the henry, volt, and ampere, 19th-century physicists worked in the centimeter-gram-second (CGS) system, which split into two competing branches: the electromagnetic (emu) branch, whose inductance unit is the abhenry (equal to a tiny one billionth of a henry), and the electrostatic (esu) branch, whose unit is the stathenry (equal to a massive 898.8 billion henries). That enormous gap — the mirror image of the abfarad/statfarad relationship in capacitance — comes from the same speed-of-light-squared relationship that links the esu and emu systems throughout classical electromagnetism. Modern electronics almost never uses either CGS unit directly, but they still turn up when translating older theoretical physics texts into today's henry-based units.

Example

An inductance of 1 nH equals 1.11265E-21 statH. For scale, a small RF inductor on a circuit board might be rated around 10 microhenries, a typical switching power-supply inductor might be a few hundred microhenries to a few millihenries, and a large mains-frequency power transformer winding can reach several henries.

Frequently Asked Questions

How many Stathenries are in 1 Nanohenry?

1 Nanohenry (nH) equals exactly 1.11265E-21 Stathenries (statH).

Why are inductors almost never rated in whole henries?

A henry is a relatively large amount of inductance to build into a small, practical coil — reaching a full henry typically requires a bulky winding around a large magnetic core, the kind used in mains-frequency transformers. Everyday inductors in power supplies, RF circuits, and filters only need a fraction of a henry, so they're rated in millihenries or microhenries instead.

Is weber/ampere the same thing as a henry?

Yes — they're mathematically identical. The henry is defined as exactly one weber of magnetic flux linkage per ampere of current (1 H = 1 Wb/A), so expressing an inductance in webers per ampere gives the exact same numeric value as expressing it in henries.

Why is the stathenry so much larger than the abhenry?

Both come from the older centimeter-gram-second (CGS) system, but from opposite branches: the abhenry is a CGS electromagnetic (emu) unit, while the stathenry is a CGS electrostatic (esu) unit. The two branches are related by the speed of light squared, which is why the abhenry (10⁻⁹ henries) and stathenry (about 8.9876 × 10¹¹ henries) sit roughly 21 orders of magnitude apart despite both measuring inductance.

What's a typical inductance value for common electronics?

It depends heavily on the application: RF and high-frequency tuning circuits often use nanohenry to microhenry inductors, switching power-supply inductors commonly range from a few microhenries to a few millihenries, and large mains-frequency transformer or motor windings can reach several henries. Kilohenry-scale inductance is essentially never seen outside specialized grid equipment.

Convert Nanohenry to Other Inductance Units

Possible Inductance Conversions

Abhenry to Millihenries Stathenry to Femtohenries Picohenry to Microhenries Kilohenry to Henries Nanohenry to Femtohenries Weber/Ampere to Abhenries Picohenry to Webers/Ampere Nanohenry to Microhenries Stathenry to Kilohenries Henry to Nanohenries Nanohenry to Picohenries Henry to Stathenries Stathenry to Picohenries Henry to Millihenries Abhenry to Microhenries Millihenry to Femtohenries Abhenry to Kilohenries Kilohenry to Nanohenries Kilohenry to Stathenries Femtohenry to Kilohenries Kilohenry to Webers/Ampere Picohenry to Abhenries Microhenry to Picohenries Picohenry to Henries Abhenry to Femtohenries Nanohenry to Webers/Ampere Weber/Ampere to Femtohenries Henry to Microhenries Stathenry to Microhenries Femtohenry to Abhenries Abhenry to Picohenries Weber/Ampere to Stathenries Millihenry to Kilohenries Kilohenry to Picohenries Microhenry to Kilohenries Kilohenry to Femtohenries Nanohenry to Millihenries Microhenry to Femtohenries Weber/Ampere to Henries Millihenry to Stathenries Henry to Abhenries Microhenry to Henries Nanohenry to Stathenries Picohenry to Stathenries Abhenry to Stathenries Microhenry to Stathenries Stathenry to Webers/Ampere Femtohenry to Picohenries Stathenry to Nanohenries Femtohenry to Stathenries Stathenry to Abhenries Femtohenry to Henries Abhenry to Henries Picohenry to Kilohenries Femtohenry to Microhenries Stathenry to Millihenries Kilohenry to Microhenries Abhenry to Webers/Ampere Henry to Webers/Ampere Stathenry to Henries Millihenry to Picohenries Millihenry to Microhenries Picohenry to Femtohenries Millihenry to Nanohenries Millihenry to Henries Millihenry to Webers/Ampere Microhenry to Millihenries Henry to Picohenries Henry to Femtohenries Kilohenry to Abhenries Picohenry to Millihenries Nanohenry to Abhenries Weber/Ampere to Kilohenries Weber/Ampere to Microhenries Weber/Ampere to Millihenries Henry to Kilohenries Weber/Ampere to Nanohenries Kilohenry to Millihenries Nanohenry to Kilohenries Picohenry to Nanohenries Femtohenry to Nanohenries Femtohenry to Millihenries Microhenry to Webers/Ampere Weber/Ampere to Picohenries Abhenry to Nanohenries Femtohenry to Webers/Ampere Microhenry to Abhenries Millihenry to Abhenries Microhenry to Nanohenries Nanohenry to Henries

See also