CalculatorBoom

Convert Femtohenries to Stathenries

Femtohenry (fH) to Stathenry (statH) inductance conversion — enter any value below to get an instant result, or use the table for common values.

Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.

The numeric value you want to convert. Decimals are accepted.

Result

1 Femtohenry = 1.11265E-27 Stathenries

1 Stathenry = 8.98755E+26 Femtohenries

1 fH in every supported unit

Conversion chart: Femtohenry to Stathenries

Conversion table

Femtohenry (fH) Stathenry (statH)
0.01 fH 1.11265E-29 statH
0.1 fH 1.11265E-28 statH
1 fH 1.11265E-27 statH
2 fH 2.2253E-27 statH
3 fH 3.33795E-27 statH
5 fH 5.56325E-27 statH
10 fH 1.11265E-26 statH
20 fH 2.2253E-26 statH
50 fH 5.56325E-26 statH
100 fH 1.11265E-25 statH
1000 fH 1.11265E-24 statH

Femtohenry (fH)

Definition: One quadrillionth of a henry (1 fH = 10⁻¹⁵ H), an extremely small inductance unit at the edge of what is practically measurable.

History: It emerged from the same SI prefix ladder used for femtofarad-scale capacitance, applied where advanced semiconductor and superconducting circuit research needed to quantify inductance below the picohenry scale.

Current use: Found mainly in advanced research contexts such as superconducting quantum circuit design and precision on-chip interconnect modeling, where inductance at this scale meaningfully influences circuit behavior.

Stathenry (statH)

Definition: The unit of inductance in the CGS electrostatic (esu) system — an enormous value equal to roughly 898.8 billion henries, arising from defining inductance through the electrostatic branch of CGS units.

History: It was derived alongside the statfarad from the electrostatic CGS system, with its huge numeric factor relative to the henry stemming from the same speed-of-light-squared relationship that links the esu and emu unit systems throughout classical electromagnetism.

Current use: Almost never used in applied engineering due to its impractically large scale relative to real inductors; it survives only in theoretical physics work that stays consistently within the Gaussian esu unit system.

Supported Units

Unit Symbol In Henry
Henry H 1 H
Kilohenry kH 1000 H
Millihenry mH 0.001 H
Microhenry µH 1E-06 H
Nanohenry nH 1E-09 H
Picohenry pH 1E-12 H
Femtohenry fH 1E-15 H
Abhenry abH 1E-09 H
Stathenry statH 8.98755E+11 H
Weber/Ampere Wb/A 1 H

About These Parameters

Value
The inductance value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a tiny nanohenry PCB-trace parasitic to a large power-transformer winding's multi-henry rating.
From Unit
The unit your input value is currently measured in — an inductor datasheet's millihenry or microhenry rating, or a historical figure quoted in abhenries or stathenries from the older CGS unit systems.
To Unit
The unit you want the result converted into. Use the swap button to flip From and To instantly, handy when translating a datasheet value into a different SI-prefixed scale or back to the base henry.

How Inductance Conversion Works

The Formula

Every unit here is defined by a fixed multiplier relative to the henry. To convert a value from one unit to another:

result = value × (factor of "From" unit ÷ factor of "To" unit)

For Femtohenry → Stathenry: multiply by 1.11265E-27. For example, 1 fH × 1.11265E-27 = 1.11265E-27 statH.

Why Inductors Span Such a Wide Range of Units

A henry is a relatively large amount of inductance for a physical coil to produce — winding enough turns around a large enough core to reach a full henry generally means a bulky component, the kind found in mains-frequency power transformers and large chokes. Most inductors used in switching power supplies, RF circuits, and signal filtering only need a fraction of a henry to do their job, which is why millihenries and microhenries are the everyday scale for real components. At the other extreme, any wire, PCB trace, or connector lead has some small amount of unavoidable "parasitic" inductance — usually measured in nanohenries or picohenries — that becomes significant only at the high frequencies and fast switching speeds used in modern digital and RF electronics.

SI Henries vs. CGS Abhenries and Stathenries

Before the SI system unified electrical units around the henry, volt, and ampere, 19th-century physicists worked in the centimeter-gram-second (CGS) system, which split into two competing branches: the electromagnetic (emu) branch, whose inductance unit is the abhenry (equal to a tiny one billionth of a henry), and the electrostatic (esu) branch, whose unit is the stathenry (equal to a massive 898.8 billion henries). That enormous gap — the mirror image of the abfarad/statfarad relationship in capacitance — comes from the same speed-of-light-squared relationship that links the esu and emu systems throughout classical electromagnetism. Modern electronics almost never uses either CGS unit directly, but they still turn up when translating older theoretical physics texts into today's henry-based units.

Example

An inductance of 1 fH equals 1.11265E-27 statH. For scale, a small RF inductor on a circuit board might be rated around 10 microhenries, a typical switching power-supply inductor might be a few hundred microhenries to a few millihenries, and a large mains-frequency power transformer winding can reach several henries.

Frequently Asked Questions

How many Stathenries are in 1 Femtohenry?

1 Femtohenry (fH) equals exactly 1.11265E-27 Stathenries (statH).

Why are inductors almost never rated in whole henries?

A henry is a relatively large amount of inductance to build into a small, practical coil — reaching a full henry typically requires a bulky winding around a large magnetic core, the kind used in mains-frequency transformers. Everyday inductors in power supplies, RF circuits, and filters only need a fraction of a henry, so they're rated in millihenries or microhenries instead.

Is weber/ampere the same thing as a henry?

Yes — they're mathematically identical. The henry is defined as exactly one weber of magnetic flux linkage per ampere of current (1 H = 1 Wb/A), so expressing an inductance in webers per ampere gives the exact same numeric value as expressing it in henries.

Why is the stathenry so much larger than the abhenry?

Both come from the older centimeter-gram-second (CGS) system, but from opposite branches: the abhenry is a CGS electromagnetic (emu) unit, while the stathenry is a CGS electrostatic (esu) unit. The two branches are related by the speed of light squared, which is why the abhenry (10⁻⁹ henries) and stathenry (about 8.9876 × 10¹¹ henries) sit roughly 21 orders of magnitude apart despite both measuring inductance.

What's a typical inductance value for common electronics?

It depends heavily on the application: RF and high-frequency tuning circuits often use nanohenry to microhenry inductors, switching power-supply inductors commonly range from a few microhenries to a few millihenries, and large mains-frequency transformer or motor windings can reach several henries. Kilohenry-scale inductance is essentially never seen outside specialized grid equipment.

Convert Femtohenry to Other Inductance Units

Possible Inductance Conversions

Microhenry to Nanohenries Henry to Stathenries Kilohenry to Webers/Ampere Abhenry to Millihenries Weber/Ampere to Picohenries Femtohenry to Millihenries Weber/Ampere to Nanohenries Stathenry to Kilohenries Henry to Kilohenries Abhenry to Microhenries Millihenry to Nanohenries Femtohenry to Microhenries Kilohenry to Picohenries Femtohenry to Webers/Ampere Abhenry to Kilohenries Nanohenry to Millihenries Nanohenry to Henries Kilohenry to Nanohenries Picohenry to Femtohenries Henry to Abhenries Kilohenry to Femtohenries Microhenry to Femtohenries Picohenry to Stathenries Millihenry to Kilohenries Millihenry to Picohenries Nanohenry to Picohenries Microhenry to Stathenries Henry to Webers/Ampere Henry to Femtohenries Stathenry to Webers/Ampere Picohenry to Kilohenries Abhenry to Picohenries Weber/Ampere to Femtohenries Microhenry to Picohenries Picohenry to Microhenries Nanohenry to Webers/Ampere Picohenry to Nanohenries Stathenry to Nanohenries Stathenry to Femtohenries Microhenry to Millihenries Microhenry to Henries Stathenry to Microhenries Nanohenry to Femtohenries Millihenry to Abhenries Kilohenry to Henries Weber/Ampere to Henries Picohenry to Henries Weber/Ampere to Kilohenries Millihenry to Stathenries Weber/Ampere to Stathenries Abhenry to Henries Abhenry to Femtohenries Stathenry to Henries Femtohenry to Henries Millihenry to Henries Weber/Ampere to Microhenries Millihenry to Microhenries Abhenry to Stathenries Femtohenry to Kilohenries Stathenry to Millihenries Abhenry to Webers/Ampere Henry to Microhenries Nanohenry to Stathenries Stathenry to Picohenries Stathenry to Abhenries Femtohenry to Abhenries Femtohenry to Stathenries Nanohenry to Kilohenries Picohenry to Millihenries Microhenry to Kilohenries Weber/Ampere to Millihenries Femtohenry to Picohenries Millihenry to Femtohenries Henry to Nanohenries Abhenry to Nanohenries Henry to Millihenries Nanohenry to Abhenries Microhenry to Abhenries Weber/Ampere to Abhenries Kilohenry to Microhenries Microhenry to Webers/Ampere Picohenry to Abhenries Nanohenry to Microhenries Femtohenry to Nanohenries Henry to Picohenries Picohenry to Webers/Ampere Kilohenry to Millihenries Kilohenry to Abhenries Kilohenry to Stathenries Millihenry to Webers/Ampere

See also