Convert Poundals to Dynes
Poundal (pdl) to Dyne (dyn) unit conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 pdl = 13825.495 dyn
1 Poundal = 13825.495 Dynes
1 Dyne = 7.23301E-05 Poundals
1 pdl in every supported unit
Conversion chart: Poundal to Dynes
Conversion table
| Poundal (pdl) | Dyne (dyn) |
|---|---|
| 0.01 pdl | 138.25495 dyn |
| 0.1 pdl | 1382.5495 dyn |
| 1 pdl | 13825.495 dyn |
| 2 pdl | 27650.991 dyn |
| 3 pdl | 41476.486 dyn |
| 5 pdl | 69127.477 dyn |
| 10 pdl | 138254.95 dyn |
| 20 pdl | 276509.91 dyn |
| 50 pdl | 691274.77 dyn |
| 100 pdl | 1382549.5 dyn |
| 1000 pdl | 13825495 dyn |
Poundal (pdl)
Definition: A force unit from the English Engineering System's alternative "absolute" branch, defined as the force that accelerates a 1-pound mass at 1 foot per second squared — the imperial analog of the newton rather than a gravitational unit.
History: Introduced in the 19th century by British engineers and physicists seeking an imperial unit of force that, like the newton, was derived purely from mass and acceleration rather than from Earth's gravity, avoiding the ambiguity of using "pound" for both mass and weight.
Current use: Rarely used today outside historical British engineering texts and some physics education contexts illustrating the mass-based vs. gravity-based unit distinction.
Dyne (dyn)
Definition: The CGS (centimeter-gram-second) unit of force, defined as the force needed to accelerate a 1-gram mass at 1 centimeter per second squared; equal to exactly 10⁻⁵ newtons.
History: Introduced in the late 19th century as part of the CGS system of units used by physicists before the SI system (built on meters, kilograms, and seconds) became the international standard in the mid-20th century.
Current use: Largely historical today, but still appears in older physics literature and in some specialized fields like surface tension measurement, which is traditionally expressed in dynes per centimeter.
Supported Units
| Unit | Symbol | In Newtons |
|---|---|---|
| Newton | N | 1 N |
| Kilonewton | kN | 1000 N |
| Dyne | dyn | 1E-05 N |
| Gram-force | gf | 0.00980665 N |
| Kilogram-force | kgf | 9.80665 N |
| Metric Ton-force | tf | 9806.65 N |
| Pound-force | lbf | 4.4482216 N |
| Ounce-force | ozf | 0.27801385 N |
| Poundal | pdl | 0.13825495 N |
| Kip-force | kip | 4448.2216 N |
About These Parameters
- Value
- The number you want to convert, expressed in the "From" unit. Accepts decimals.
- From Unit
- The force unit your input value is currently measured in.
- To Unit
- The force unit you want the result converted into. Use the swap button to flip From and To instantly.
How Force Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the newton. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Poundal → Dyne: multiply by 13825.495. For example, 1 pdl × 13825.495 = 13825.495 dyn.
Force vs. Mass: A Common Point of Confusion
Force and mass are not the same thing, even though units like kilogram-force make them look related. A kilogram is a unit of mass — how much matter an object contains — while a kilogram-force is a unit of force: specifically, the weight (gravitational pull) exerted on a 1 kg mass at Earth's surface. Mass stays the same anywhere in the universe; weight changes with gravity, so a 1 kg mass weighs 1 kgf on Earth but would weigh far less on the Moon. Newtons, pound-force, and the other units on this page all measure force (or weight), never mass.
SI vs. US Customary and Engineering Units
The newton is the SI standard and the default unit in physics, mechanical engineering, and international science everywhere. US structural and civil engineers instead work primarily in pound-force and, for large loads, kips (1,000 lbf) — the customary units baked into American building codes. Kilogram-force and metric ton-force persist informally in parts of Europe and Asia for everyday load ratings even though they were formally superseded by the newton decades ago, and the dyne survives mainly in older CGS-based physics literature and a handful of specialized surface-tension measurements.
Example
1 pdl equals 13825.495 dyn. For scale, that's about 0.14× the weight of an average apple (roughly 1 N, or 7.2330138 pdl) — and a 150 lb (about 667 N) adult's body weight would be roughly 4824.4202 pdl.
Frequently Asked Questions
How many Dynes are in 1 Poundal?
1 Poundal (pdl) equals exactly 13825.495 Dynes (dyn).
What's the difference between kilogram and kilogram-force?
A kilogram measures mass, an intrinsic property of an object that never changes. A kilogram-force measures the weight (force) that Earth's gravity exerts on a 1 kg mass — 9.80665 newtons. The two are related by gravity, not interchangeable, which is why kilogram-force is considered a legacy "gravitational" unit rather than a proper SI unit.
Why do engineers use kips?
Structural loads on buildings and bridges routinely run into the hundreds of thousands of pounds-force. Expressing a beam's load capacity as "150,000 lbf" is unwieldy, so American structural engineers use the kip (1,000 lbf) to keep numbers compact and readable — "150 kip" instead — the same reasoning that leads metric engineers to prefer kilonewtons over newtons for large loads.
How accurate are these conversions?
Every conversion factor used here is the exact, internationally recognized value (e.g. 1 lbf = exactly 4.4482216152605 N, derived from the internationally standardized pound and standard gravity) — results are limited only by floating-point display precision, not by rounded conversion constants.