Convert Pounds per Gallon (UK) to Kilograms per Liter
Pound per Gallon (UK) (lb/gal(UK)) to Kilogram per Liter (kg/L) solution concentration conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 lb/gal(UK) = 0.099776374 kg/L
1 Pound per Gallon (UK) = 0.099776374 Kilograms per Liter
1 Kilogram per Liter = 10.022413 Pounds per Gallon (UK)
1 lb/gal(UK) in every supported unit
Conversion chart: Pound per Gallon (UK) to Kilograms per Liter
Conversion table
| Pound per Gallon (UK) (lb/gal(UK)) | Kilogram per Liter (kg/L) |
|---|---|
| 0.01 lb/gal(UK) | 0.00099776374 kg/L |
| 0.1 lb/gal(UK) | 0.0099776374 kg/L |
| 1 lb/gal(UK) | 0.099776374 kg/L |
| 2 lb/gal(UK) | 0.19955275 kg/L |
| 3 lb/gal(UK) | 0.29932912 kg/L |
| 5 lb/gal(UK) | 0.49888187 kg/L |
| 10 lb/gal(UK) | 0.99776374 kg/L |
| 20 lb/gal(UK) | 1.9955275 kg/L |
| 50 lb/gal(UK) | 4.9888187 kg/L |
| 100 lb/gal(UK) | 9.9776374 kg/L |
| 1000 lb/gal(UK) | 99.776374 kg/L |
Pound per Gallon (UK) (lb/gal(UK))
Definition: The imperial counterpart to pound per US gallon, expressing pounds of solute per UK (imperial) gallon of solution.
History: Used in British and Commonwealth industrial chemistry following the imperial gallon standard, distinct from the US gallon by roughly 20% in volume.
Current use: Found on legacy UK industrial and agricultural chemical specifications, though largely superseded by metric kg/L and g/L reporting in current British practice.
Kilogram per Liter (kg/L)
Definition: The base unit for this converter — the mass in kilograms of solute dissolved in one liter of solution, giving a direct mass-per-volume concentration figure.
History: A straightforward combination of the SI kilogram and liter, adopted as solution concentration became a standard quantity in chemistry and industrial process engineering during the metrication of scientific units.
Current use: Used for high-concentration solutions in industrial chemistry, brine and slurry density specifications, and process engineering where solute loads are large relative to the solvent.
Supported Units
| Unit | Symbol | In kg/L |
|---|---|---|
| Kilogram per Liter | kg/L | 1 kg/L |
| Gram per Liter | g/L | 0.001 kg/L |
| Milligram per Liter | mg/L | 1E-06 kg/L |
| Part per Million | ppm | 9.98859E-07 kg/L |
| Grain per Gallon (US) | gr/gal(US) | 1.71181E-05 kg/L |
| Grain per Gallon (UK) | gr/gal(UK) | 1.42538E-05 kg/L |
| Pound per Gallon (US) | lb/gal(US) | 0.11982643 kg/L |
| Pound per Gallon (UK) | lb/gal(UK) | 0.099776374 kg/L |
| Pound per Million Gallon (US) | lb/Mgal(US) | 1.19826E-07 kg/L |
| Pound per Cubic Foot | lb/ft³ | 0.016018463 kg/L |
About These Parameters
- Value
- The solution concentration value you want to convert, expressed in the "From" unit. Accepts decimals.
- From Unit
- The unit your input value is currently measured in — a water-quality report's mg/L, or a hardness test kit's grains per gallon.
- To Unit
- The unit you want the result converted into. Use the swap button to flip From and To instantly.
How Concentration - Solution Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to kilograms per liter. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Pound per Gallon (UK) → Kilogram per Liter: multiply by 0.099776374. For example, 1 lb/gal(UK) × 0.099776374 = 0.099776374 kg/L.
Solution Concentration vs. Molar Concentration
This page covers MASS-basis concentration — mass of solute per unit volume of solution, such as mg/L or lb/gal. The site's separate Concentration - Molar Converter covers MOLE-basis concentration (e.g. moles per liter, "molarity"), which counts particles of solute rather than their mass. Converting between the two requires knowing the solute's molar mass: dividing a mass-basis concentration by the molar mass gives the mole-basis concentration, and multiplying a mole-basis concentration by the molar mass gives the mass-basis figure back.
Understanding Water Hardness
Grains per gallon and parts per million (ppm) are the two units the water-treatment industry relies on to describe hardness — the concentration of dissolved calcium and magnesium minerals in water. One grain per gallon (US) equals roughly 17.1 mg/L (approximately 17.1 ppm on a mass basis), and water-softener systems are typically sized in "grains of capacity" against a measured grains-per-gallon hardness figure. Water below about 1 gr/gal is considered soft, while water above 10-15 gr/gal is considered very hard.
Example
A solution concentration of 1 lb/gal(UK) equals 0.099776374 kg/L. For scale, US drinking-water standards generally set contaminant limits in the low single-digit mg/L range, while a moderately hard tap water might test around 7-10 grains per gallon (roughly 120-170 mg/L of hardness minerals).
Frequently Asked Questions
How many Kilograms per Liter are in 1 Pound per Gallon (UK)?
1 Pound per Gallon (UK) (lb/gal(UK)) equals exactly 0.099776374 Kilograms per Liter (kg/L).
What does ppm mean in water testing?
In water testing, ppm (parts per million) is almost always used on a mass basis, meaning one milligram of solute per kilogram (roughly one liter) of water — which is why ppm and mg/L are treated as effectively interchangeable for dilute aqueous solutions, even though the two units are defined differently in principle.
What's a grain per gallon?
A grain per gallon (US) is a traditional water-hardness unit equal to one grain (1/7,000 of a pound) of dissolved mineral per US gallon of water, roughly 17.1 mg/L — it remains the standard unit on US water-softener sizing charts and hardness test strips even though most other concentration measurements have moved to metric mg/L.
How accurate are these conversions?
Every conversion factor used here is the standard, internationally recognized relationship between the underlying mass and volume units — results are limited only by floating-point display precision, not by rounded conversion constants.