Convert Grains per Gallon (UK) to Milligrams per Liter
Grain per Gallon (UK) (gr/gal(UK)) to Milligram per Liter (mg/L) solution concentration conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 gr/gal(UK) = 14.2538 mg/L
1 Grain per Gallon (UK) = 14.2538 Milligrams per Liter
1 Milligram per Liter = 0.07015673 Grains per Gallon (UK)
1 gr/gal(UK) in every supported unit
Conversion chart: Grain per Gallon (UK) to Milligrams per Liter
Conversion table
| Grain per Gallon (UK) (gr/gal(UK)) | Milligram per Liter (mg/L) |
|---|---|
| 0.01 gr/gal(UK) | 0.142538 mg/L |
| 0.1 gr/gal(UK) | 1.42538 mg/L |
| 1 gr/gal(UK) | 14.2538 mg/L |
| 2 gr/gal(UK) | 28.5076 mg/L |
| 3 gr/gal(UK) | 42.7614 mg/L |
| 5 gr/gal(UK) | 71.269 mg/L |
| 10 gr/gal(UK) | 142.538 mg/L |
| 20 gr/gal(UK) | 285.076 mg/L |
| 50 gr/gal(UK) | 712.69 mg/L |
| 100 gr/gal(UK) | 1425.38 mg/L |
| 1000 gr/gal(UK) | 14253.8 mg/L |
Grain per Gallon (UK) (gr/gal(UK))
Definition: The same grain-based concentration measure as its US counterpart, but referenced to the larger UK (imperial) gallon, giving a slightly different numeric conversion factor.
History: Developed alongside British water-hardness testing standards using the imperial gallon, which is about 20% larger than the US gallon, producing a lower grains-per-gallon figure for the same actual concentration.
Current use: Occasionally seen on older or UK-sourced water-hardness charts and softener specifications, though most UK water utilities today report hardness in mg/L or degrees Clark.
Milligram per Liter (mg/L)
Definition: A trace-concentration unit — milligrams of solute per liter of solution — commonly treated as numerically equivalent to parts per million for dilute aqueous solutions near water's density.
History: Adopted by environmental and water chemistry as laboratory instruments became sensitive enough to detect solute levels at the milligram scale, replacing older, less precise trace-concentration expressions.
Current use: The standard unit on drinking-water quality reports, wastewater discharge permits, and environmental contaminant testing worldwide.
Supported Units
| Unit | Symbol | In kg/L |
|---|---|---|
| Kilogram per Liter | kg/L | 1 kg/L |
| Gram per Liter | g/L | 0.001 kg/L |
| Milligram per Liter | mg/L | 1E-06 kg/L |
| Part per Million | ppm | 9.98859E-07 kg/L |
| Grain per Gallon (US) | gr/gal(US) | 1.71181E-05 kg/L |
| Grain per Gallon (UK) | gr/gal(UK) | 1.42538E-05 kg/L |
| Pound per Gallon (US) | lb/gal(US) | 0.11982643 kg/L |
| Pound per Gallon (UK) | lb/gal(UK) | 0.099776374 kg/L |
| Pound per Million Gallon (US) | lb/Mgal(US) | 1.19826E-07 kg/L |
| Pound per Cubic Foot | lb/ft³ | 0.016018463 kg/L |
About These Parameters
- Value
- The solution concentration value you want to convert, expressed in the "From" unit. Accepts decimals.
- From Unit
- The unit your input value is currently measured in — a water-quality report's mg/L, or a hardness test kit's grains per gallon.
- To Unit
- The unit you want the result converted into. Use the swap button to flip From and To instantly.
How Concentration - Solution Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to kilograms per liter. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Grain per Gallon (UK) → Milligram per Liter: multiply by 14.2538. For example, 1 gr/gal(UK) × 14.2538 = 14.2538 mg/L.
Solution Concentration vs. Molar Concentration
This page covers MASS-basis concentration — mass of solute per unit volume of solution, such as mg/L or lb/gal. The site's separate Concentration - Molar Converter covers MOLE-basis concentration (e.g. moles per liter, "molarity"), which counts particles of solute rather than their mass. Converting between the two requires knowing the solute's molar mass: dividing a mass-basis concentration by the molar mass gives the mole-basis concentration, and multiplying a mole-basis concentration by the molar mass gives the mass-basis figure back.
Understanding Water Hardness
Grains per gallon and parts per million (ppm) are the two units the water-treatment industry relies on to describe hardness — the concentration of dissolved calcium and magnesium minerals in water. One grain per gallon (US) equals roughly 17.1 mg/L (approximately 17.1 ppm on a mass basis), and water-softener systems are typically sized in "grains of capacity" against a measured grains-per-gallon hardness figure. Water below about 1 gr/gal is considered soft, while water above 10-15 gr/gal is considered very hard.
Example
A solution concentration of 1 gr/gal(UK) equals 14.2538 mg/L. For scale, US drinking-water standards generally set contaminant limits in the low single-digit mg/L range, while a moderately hard tap water might test around 7-10 grains per gallon (roughly 120-170 mg/L of hardness minerals).
Frequently Asked Questions
How many Milligrams per Liter are in 1 Grain per Gallon (UK)?
1 Grain per Gallon (UK) (gr/gal(UK)) equals exactly 14.2538 Milligrams per Liter (mg/L).
What does ppm mean in water testing?
In water testing, ppm (parts per million) is almost always used on a mass basis, meaning one milligram of solute per kilogram (roughly one liter) of water — which is why ppm and mg/L are treated as effectively interchangeable for dilute aqueous solutions, even though the two units are defined differently in principle.
What's a grain per gallon?
A grain per gallon (US) is a traditional water-hardness unit equal to one grain (1/7,000 of a pound) of dissolved mineral per US gallon of water, roughly 17.1 mg/L — it remains the standard unit on US water-softener sizing charts and hardness test strips even though most other concentration measurements have moved to metric mg/L.
How accurate are these conversions?
Every conversion factor used here is the standard, internationally recognized relationship between the underlying mass and volume units — results are limited only by floating-point display precision, not by rounded conversion constants.