Convert Pounds per Square Inch to Inches of Mercury
Pound per Square Inch (psi) to Inch of Mercury (inHg) unit conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 psi = 2.0360259 inHg
1 Pound per Square Inch = 2.0360259 Inches of Mercury
1 Inch of Mercury = 0.49115289 Pounds per Square Inch
1 psi in every supported unit
Conversion chart: Pound per Square Inch to Inches of Mercury
Conversion table
| Pound per Square Inch (psi) | Inch of Mercury (inHg) |
|---|---|
| 0.01 psi | 0.020360259 inHg |
| 0.1 psi | 0.20360259 inHg |
| 1 psi | 2.0360259 inHg |
| 2 psi | 4.0720517 inHg |
| 3 psi | 6.1080776 inHg |
| 5 psi | 10.180129 inHg |
| 10 psi | 20.360259 inHg |
| 20 psi | 40.720517 inHg |
| 50 psi | 101.80129 inHg |
| 100 psi | 203.60259 inHg |
| 1000 psi | 2036.0259 inHg |
Pound per Square Inch (psi)
Definition: The pressure exerted by one pound-force distributed evenly over an area of one square inch.
History: Grew out of the British imperial system of weights and measures used throughout the 19th and 20th centuries, and remained the standard pressure unit in the United States even after most of the world adopted metric units.
Current use: The everyday pressure unit in the United States, used for vehicle and bicycle tire pressure, household water pressure, and pressure ratings printed on tools, hoses, and tanks.
Inch of Mercury (inHg)
Definition: The pressure exerted by a column of mercury one inch tall under standard gravity, a direct manometer-based unit of measurement.
History: Developed alongside early mercury barometers in the 17th and 18th centuries, when pressure was measured directly by the height of mercury it could support inside a sealed glass tube.
Current use: Used in United States weather reports for barometric pressure and in aviation altimeter settings, where pilots dial in the local pressure reading in inches of mercury.
Supported Units
| Unit | Symbol | In Pascals |
|---|---|---|
| Pascal | Pa | 1 Pa |
| Kilopascal | kPa | 1000 Pa |
| Megapascal | MPa | 1000000 Pa |
| Hectopascal | hPa | 100 Pa |
| Bar | bar | 100000 Pa |
| Millibar | mbar | 100 Pa |
| Pound per Square Inch | psi | 6894.7573 Pa |
| Standard Atmosphere | atm | 101325 Pa |
| Torr | Torr | 133.32237 Pa |
| Inch of Mercury | inHg | 3386.38 Pa |
About These Parameters
- Value
- The pressure reading you want to convert, expressed in the "From" unit. Accepts decimals.
- From Unit
- The pressure scale your input value is currently measured in — for example, PSI on a US tire gauge or hectopascals on a weather report.
- To Unit
- The pressure scale you want the result converted into. Use the swap button to flip From and To instantly.
How Pressure Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the pascal. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Pound per Square Inch → Inch of Mercury: multiply by 2.0360259. For example, 1 psi × 2.0360259 = 2.0360259 inHg.
SI vs. Customary Units
The metric units on this page — pascal, kilopascal, megapascal, hectopascal, bar, and millibar — all scale by powers of ten, so converting between them is just moving a decimal point. PSI is a US customary unit built from pounds-force and square inches, unrelated to the metric scale, while torr and inches of mercury are older manometer-based units defined by the height of a mercury column a pressure could support — each needs its own precise multiplier rather than a round decimal shift.
Why Atmospheric Pressure Matters
Standard atmospheric pressure — 101,325 Pa, or 1 atm — is the reference point most pressure units are built around, because it is the pressure every person and machine on Earth's surface experiences by default. Meteorologists track small deviations from this baseline, measured in hectopascals or millibars, to forecast weather: a falling barometer reading signals an approaching low-pressure system and possible storms, while a rising one signals clear, stable conditions.
Example
1 psi equals 2.0360259 inHg. For scale, that's about 0.07× standard atmospheric pressure (1 atm, or 14.695949 psi) — roughly the pressure difference a typical car tire holds above the surrounding air (about 32 psi, or 2.2 bar).
Frequently Asked Questions
How many Inches of Mercury are in 1 Pound per Square Inch?
1 Pound per Square Inch (psi) equals exactly 2.0360259 Inches of Mercury (inHg).
Why do US tire gauges use PSI?
The United States never mandated metrication, so pounds and inches stayed the default units for everyday measurement, including the pound-force-per-square-inch pressure scale used on tire gauges, plumbing fixtures, and compressed air tools. Most of the rest of the world reads the same measurement in bar or kilopascals.
What's the difference between a bar and an atmosphere?
A bar is a round metric unit equal to exactly 100,000 pascals, chosen for convenient arithmetic; a standard atmosphere is fixed at exactly 101,325 pascals, the measured average air pressure at sea level. The two are close — 1 atm is about 1.01325 bar — but they are defined differently and are not interchangeable in precise scientific work.
How accurate are these conversions?
Every conversion factor used here is the exact, internationally standardized value (e.g. 1 atm = exactly 101,325 Pa, and 1 psi = exactly 6,894.7572931783 Pa) — results are limited only by floating-point display precision, not by rounded conversion constants.