Convert Kiloohms to Volt/Amperes
Kiloohm (kΩ) to Volt/Ampere (V/A) electric resistance conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 kΩ = 1000 V/A
1 Kiloohm = 1000 Volt/Amperes
1 Volt/Ampere = 0.001 Kiloohms
1 kΩ in every supported unit
Conversion chart: Kiloohm to Volt/Amperes
Conversion table
| Kiloohm (kΩ) | Volt/Ampere (V/A) |
|---|---|
| 0.01 kΩ | 10 V/A |
| 0.1 kΩ | 100 V/A |
| 1 kΩ | 1000 V/A |
| 2 kΩ | 2000 V/A |
| 3 kΩ | 3000 V/A |
| 5 kΩ | 5000 V/A |
| 10 kΩ | 10000 V/A |
| 20 kΩ | 20000 V/A |
| 50 kΩ | 50000 V/A |
| 100 kΩ | 100000 V/A |
| 1000 kΩ | 1000000 V/A |
Kiloohm (kΩ)
Definition: The SI multiple equal to 1,000 ohms, used whenever a plain ohm figure would be inconveniently large to read, write, or compare.
History: Formed by combining the standard SI "kilo-" prefix with the ohm as electronics moved from simple low-resistance circuits toward the much higher resistor values common in transistor and integrated-circuit design.
Current use: One of the most commonly printed resistor value ranges in electronics — pull-up and pull-down resistors, voltage-divider networks, and potentiometers are routinely specified in kiloohms, such as a 4.7 kΩ or 10 kΩ resistor.
Volt/Ampere (V/A)
Definition: The dimensional expansion of Ohm's law itself — a volt per ampere is, by definition, numerically and dimensionally identical to an ohm, since resistance is defined as voltage divided by current (R = V / I).
History: This form predates the ohm's adoption as a distinct named unit in 1881; before that, physicists and engineers expressed resistance directly in terms of its constituent electrical quantities rather than using a dedicated symbol.
Current use: Still used in physics and engineering derivations when a calculation's units are being carried through explicitly from voltage and current rather than jumping straight to the shorthand ohm.
Supported Units
| Unit | Symbol | In Ohm |
|---|---|---|
| Ohm | Ω | 1 Ω |
| Kiloohm | kΩ | 1000 Ω |
| Megohm | MΩ | 1000000 Ω |
| Milliohm | mΩ | 0.001 Ω |
| Microhm | μΩ | 1E-06 Ω |
| Volt/Ampere | V/A | 1 Ω |
| Reciprocal Siemens | 1/S | 1 Ω |
| Abohm | abΩ | 1E-09 Ω |
| EMU of Resistance | EMU | 1E-09 Ω |
| Statohm | statΩ | 8.98755E+11 Ω |
| ESU of Resistance | ESU | 8.98755E+11 Ω |
| Quantized Hall Resistance | R_K | 25812.807 Ω |
About These Parameters
- Value
- The electric resistance value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a microhm-scale connector contact resistance to a megohm-scale insulation-resistance reading.
- From Unit
- The unit your input value is currently measured in — a resistor's printed ohm or kiloohm rating, a megohmmeter's insulation reading, or an older figure quoted in a CGS unit like the abohm or statohm.
- To Unit
- The unit you want the result converted into. Use the swap button to flip From and To instantly, which is handy when moving between a datasheet's units and the ones used in your own calculations.
How Electric Resistance Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the ohm. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Kiloohm → Volt/Ampere: multiply by 1000. For example, 1 kΩ × 1000 = 1000 V/A.
Ohm's Law and the Origin of the Ohm
Georg Simon Ohm published his now-famous law in 1827, showing that the current through a conductor is directly proportional to the voltage across it and inversely proportional to its resistance — a relationship so fundamental that essentially every electrical calculation traces back to it. At the time his work was met with skepticism and largely ignored by the German physics establishment; recognition came only later, and it wasn't until the International Electrical Congress of 1881 that "ohm" was formally adopted as the name of the resistance unit, defined so that one ohm is the resistance that lets one ampere flow when one volt is applied. Every SI multiple on this page — from milliohm up through megohm — is simply that same unit scaled by a power of ten for convenience.
Why CGS Resistance Units Still Appear
Before the SI system unified electrical units around the ampere, 19th-century physicists worked with two parallel centimeter-gram-second (CGS) systems: the electromagnetic (EMU) system, which gave us the abohm, and the electrostatic (ESU) system, which gave us the statohm — a unit so much larger than the ohm that it differs by a factor tied to the speed of light. Both systems were mathematically elegant for theoretical physics but impractical for engineering, which is why they were eventually superseded by the ampere-based SI units used almost everywhere today. They still turn up when reading historical electromagnetism papers or textbooks written in Gaussian units.
Example
An electric resistance of 1 kΩ equals 1000 V/A. For scale, a typical carbon-film resistor might be rated between 100 ohms and a few megohms, a copper shunt used for current sensing might measure just a few milliohms, and a healthy insulation-resistance test on household wiring should read well into the megohms.
Frequently Asked Questions
How many Volt/Amperes are in 1 Kiloohm?
1 Kiloohm (kΩ) equals exactly 1000 Volt/Amperes (V/A).
What's the difference between resistance and resistivity?
Resistance (measured in ohms) depends on a specific object's shape — its length and cross-sectional area — as well as the material it's made of. Resistivity (measured in ohm-meters) is a pure material property that stays the same regardless of the object's dimensions. Two wires of the same copper have the same resistivity, but a longer or thinner wire will have higher resistance. See the separate Electric Resistivity Converter for that quantity.
Is volt/ampere the same thing as an ohm?
Yes — they're numerically and dimensionally identical. The ohm is simply the named SI unit for the quantity that Ohm's law defines as voltage divided by current, so 1 V/A always equals exactly 1 Ω.
Why is the statohm so much larger than the ohm?
The statohm comes from the CGS electrostatic (ESU) unit system, which was built directly from Coulomb's law rather than the ampere-based definitions SI units use. The huge gap between the statohm and the ohm — roughly a factor of 9×10¹¹ — traces back to a conversion constant related to the speed of light that separates the electrostatic and electromagnetic CGS unit families.
What is quantized Hall resistance used for?
It's a fundamental resistance value, R_K = h/e², that appears as extremely precise, naturally quantized plateaus in the quantum Hall effect. Since 1990, national metrology institutes have used a fixed conventional value of this constant (25,812.807 ohms) as the international standard for calibrating precision resistance measurements, because it's far more reproducible than any physical resistor.