Convert Pound Square Inches to Kilogram Square Centimeters
Pound Square Inch (lb·in²) to Kilogram Square Centimeter (kg·cm²) unit conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 lb·in² = 2.926397 kg·cm²
1 Pound Square Inch = 2.926397 Kilogram Square Centimeters
1 Kilogram Square Centimeter = 0.34171714 Pound Square Inches
1 lb·in² in every supported unit
Conversion chart: Pound Square Inch to Kilogram Square Centimeters
Conversion table
| Pound Square Inch (lb·in²) | Kilogram Square Centimeter (kg·cm²) |
|---|---|
| 0.01 lb·in² | 0.02926397 kg·cm² |
| 0.1 lb·in² | 0.2926397 kg·cm² |
| 1 lb·in² | 2.926397 kg·cm² |
| 2 lb·in² | 5.852794 kg·cm² |
| 3 lb·in² | 8.779191 kg·cm² |
| 5 lb·in² | 14.631985 kg·cm² |
| 10 lb·in² | 29.26397 kg·cm² |
| 20 lb·in² | 58.52794 kg·cm² |
| 50 lb·in² | 146.31985 kg·cm² |
| 100 lb·in² | 292.6397 kg·cm² |
| 1000 lb·in² | 2926.397 kg·cm² |
Pound Square Inch (lb·in²)
Definition: A finer US customary moment of inertia unit equal to the rotational inertia of a 1-pound mass located 1 inch from the rotation axis.
History: Derived from pound square foot via the standard 144 square-inches-per-square-foot relationship, used when foot-scale units would understate the precision needed for smaller rotating parts.
Current use: Applied in the design of small mechanical components — gears, pulleys, small shafts — in US manufacturing where inch-based dimensioning is standard.
Kilogram Square Centimeter (kg·cm²)
Definition: A smaller-scale metric moment of inertia unit, equal to the rotational inertia of a 1 kg mass located 1 centimeter from the rotation axis.
History: A straightforward centimeter-scaled variant of the SI unit, used wherever the components being analyzed are small enough that kilogram square meters would produce inconveniently small decimal values.
Current use: Common in mechanical component design — gears, small motors, precision instruments — where dimensions are naturally measured in centimeters rather than meters.
Supported Units
| Unit | Symbol | In Kilogram Square Meters |
|---|---|---|
| Kilogram Square Meter | kg·m² | 1 kg·m² |
| Kilogram Square Centimeter | kg·cm² | 0.0001 kg·m² |
| Kilogram Square Millimeter | kg·mm² | 1E-06 kg·m² |
| Gram Square Centimeter | g·cm² | 1E-07 kg·m² |
| Gram Square Millimeter | g·mm² | 1E-09 kg·m² |
| Pound Square Foot | lb·ft² | 0.04214011 kg·m² |
| Pound Square Inch | lb·in² | 0.0002926397 kg·m² |
| Ounce Square Inch | oz·in² | 1.829E-05 kg·m² |
| Slug Square Foot | slug·ft² | 1.355818 kg·m² |
About These Parameters
- Value
- The number you want to convert, expressed in the "From" unit. Accepts decimals.
- From Unit
- The moment of inertia unit your input value is currently measured in.
- To Unit
- The moment of inertia unit you want the result converted into. Use the swap button to flip From and To instantly.
How Moment of Inertia Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the kilogram square meter. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Pound Square Inch → Kilogram Square Centimeter: multiply by 2.926397. For example, 1 lb·in² × 2.926397 = 2.926397 kg·cm².
Moment of Inertia vs. Mass: Distribution Matters
Mass tells you how much matter an object has; moment of inertia tells you how hard it is to spin that object, and the two are not simply proportional. For a point mass m at distance r from the rotation axis, moment of inertia is I = m·r² — the distance is squared, so mass located far from the axis contributes far more resistance to rotation than the same mass located close to it. This is why a solid disk and a thin ring of identical mass and radius have different moments of inertia (the ring's mass all sits at the rim, at maximum distance), and why figure skaters spin faster by pulling their arms in — reducing r reduces I, and angular momentum conservation forces angular velocity to increase.
SI vs. US Customary Engineering Units
The kilogram square meter is the SI standard used in physics and mechanical engineering worldwide. US automotive and aerospace engineers instead work in pound square foot or, when applying Newton's second law directly without conversion factors, the slug square foot — built on the slug, the US customary mass unit defined so that a 1 lbf force accelerates a 1-slug mass at exactly 1 ft/s². Smaller components — gears, motors, precision instruments — are typically specified in centimeter, millimeter, or inch-based variants to keep the numbers in a readable range for their scale.
Example
1 lb·in² equals 2.926397 kg·cm². For scale, a small automotive flywheel might have a moment of inertia around 0.5 kg·m² — about 1708.5857 lb·in² — meaning it takes a torque of 0.5 N·m to give it an angular acceleration of exactly 1 radian per second squared.
Frequently Asked Questions
How many Kilogram Square Centimeters are in 1 Pound Square Inch?
1 Pound Square Inch (lb·in²) equals exactly 2.926397 Kilogram Square Centimeters (kg·cm²).
What's the difference between moment of inertia and mass?
Mass measures how much matter an object contains and resists linear acceleration; moment of inertia measures how that mass is distributed around a rotation axis and resists angular acceleration. Two objects with identical mass can have very different moments of inertia depending on how far their mass sits from the axis — a ring resists spinning far more than a solid disk of the same mass and radius.
Why does the US customary system use the slug?
The slug is the US customary unit of mass defined so that Newton's second law (F = ma) and its rotational analog (torque = I·α) work directly with pound-force and foot units, without extra conversion factors. Using ordinary "pounds" for both force and mass creates ambiguity, so engineering calculations that need internal consistency use the slug and slug square foot instead.
How accurate are these conversions?
Every conversion factor used here is derived from the exact, internationally recognized definitions of the underlying mass and length units (the international pound, the international foot, and the slug's definition from pound-force and standard gravity) — results are limited only by floating-point display precision, not by rounded conversion constants.