Convert Watts/Ampere to Statvolts
Watt/Ampere (W/A) to Statvolt (stV) electric potential conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 W/A = 0.0033356405 stV
1 Watt/Ampere = 0.0033356405 Statvolts
1 Statvolt = 299.7925 Watts/Ampere
1 W/A in every supported unit
Conversion chart: Watt/Ampere to Statvolts
Conversion table
| Watt/Ampere (W/A) | Statvolt (stV) |
|---|---|
| 0.01 W/A | 3.33564E-05 stV |
| 0.1 W/A | 0.00033356405 stV |
| 1 W/A | 0.0033356405 stV |
| 2 W/A | 0.006671281 stV |
| 3 W/A | 0.010006921 stV |
| 5 W/A | 0.016678202 stV |
| 10 W/A | 0.033356405 stV |
| 20 W/A | 0.06671281 stV |
| 50 W/A | 0.16678202 stV |
| 100 W/A | 0.33356405 stV |
| 1000 W/A | 3.3356405 stV |
Watt/Ampere (W/A)
Definition: The electric potential expressed through its defining relationship to power and current — since power equals voltage times current (P = VI), one watt per ampere is dimensionally and numerically identical to one volt.
History: It emerges directly from the SI's coherent derived-unit system once both the watt (a unit of power) and the ampere (the SI base unit of current) were formally defined, giving voltage a self-consistent expression alongside the rest of electrical engineering.
Current use: Used interchangeably with the volt in technical and engineering contexts, particularly when a calculation's derivation naturally passes through power and current rather than starting from voltage directly.
Statvolt (stV)
Definition: The base unit of electric potential in the CGS electrostatic (ESU) system, defined directly from Coulomb's law so that one statvolt equals about 299.79 volts.
History: Derived from the electrostatic CGS system's charge unit, the statcoulomb, and its energy unit, the erg, without the vacuum permittivity constant the SI carries — the statvolt's numerical relationship to the volt traces back to the same speed-of-light-derived factor that separates the CGS electrostatic and electromagnetic unit families.
Current use: Still favored in theoretical physics and plasma/astrophysics derivations that use Gaussian units for the elegance they bring to Maxwell's equations, though almost entirely absent from modern engineering practice.
Supported Units
| Unit | Symbol | In Volt |
|---|---|---|
| Volt | V | 1 V |
| Kilovolt | kV | 1000 V |
| Millivolt | mV | 0.001 V |
| Microvolt | µV | 1E-06 V |
| Megavolt | MV | 1000000 V |
| Watt/Ampere | W/A | 1 V |
| Abvolt | abV | 1E-08 V |
| EMU of Electric Potential | EMU | 1E-08 V |
| Statvolt | stV | 299.7925 V |
| ESU of Electric Potential | ESU | 299.7925 V |
About These Parameters
- Value
- The electric potential (voltage) value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a microvolt-scale sensor signal to a megavolt-scale high-voltage test figure.
- From Unit
- The unit your input value is currently measured in — a modern spec sheet's volt, kilovolt, or millivolt rating, or a historical figure quoted in abvolts, statvolts, or another CGS-Gaussian electric potential unit.
- To Unit
- The unit you want the result converted into. Use the swap button to flip From and To instantly, which is handy when translating an older CGS-based figure into the modern SI volt or vice versa.
How Electric Potential Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the volt. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Watt/Ampere → Statvolt: multiply by 0.0033356405. For example, 1 W/A × 0.0033356405 = 0.0033356405 stV.
From CGS to SI
Before the SI system unified electrical measurement, 19th-century physicists worked with two parallel centimeter-gram-second (CGS) unit families: the electromagnetic system (CGS-EMU), whose potential unit was the abvolt (also called "EMU of electric potential"), and the electrostatic system (CGS-ESU), whose potential unit was the statvolt (also called "ESU of electric potential"). The two families differ enormously in scale — one abvolt equals a hundred-millionth of a volt, while one statvolt equals roughly 299.79 volts — because they were built from Coulomb's law and the electromagnetic force law using different fundamental scaling assumptions, with the ratio between the two systems tracing back to the speed of light. The modern volt, formally adopted in 1881 and later folded into the coherent SI, replaced both CGS conventions with a single reproducible standard.
Why Watt/Ampere Equals a Volt
Electric power equals voltage times current (P = VI), so rearranging that relationship gives voltage as power divided by current — one watt of power per ampere of current is therefore dimensionally and numerically identical to one volt. This isn't a separate physical unit being converted into the volt; it's the same quantity written in its underlying SI derived-unit form, which is why the conversion factor between watt/ampere and volt is exactly 1. The same logic explains why abvolt and "EMU of electric potential" are exact synonyms, and why statvolt and "ESU of electric potential" are exact synonyms — each pair is one physical quantity carrying two historical names from the same 19th-century CGS labeling convention.
Example
An electric potential of 1 W/A equals 0.0033356405 stV. For scale, a AA battery supplies about 1.5 volts, a US household wall outlet delivers around 120 volts, and a long-distance power transmission line can carry several hundred kilovolts between substations.
Frequently Asked Questions
How many Statvolts are in 1 Watt/Ampere?
1 Watt/Ampere (W/A) equals exactly 0.0033356405 Statvolts (stV).
What is the difference between volt and millivolt?
A millivolt is one-thousandth of a volt (1 mV = 0.001 V). The volt is the everyday unit for batteries and mains power, while the millivolt is the practical unit for the much smaller potentials typical of sensors, thermocouples, and biosignal readings like ECG traces.
Are abvolt and EMU of electric potential really the same unit?
Yes — both names refer to the identical CGS-electromagnetic potential unit, equal to exactly one hundred-millionth of a volt. They arose from different naming conventions used in 19th- and early 20th-century physics literature rather than representing physically distinct quantities.
Why is a statvolt so much larger than a volt?
The statvolt comes from the CGS electrostatic unit system, built directly from Coulomb's law without the SI's scaling conventions. The roughly 300x size gap between it and the volt traces back to the speed of light, which relates the electrostatic and electromagnetic CGS unit families to each other.
Is watt/ampere really the same as a volt?
Yes — since power equals voltage times current (P = VI), one watt per ampere is exactly equal to one volt by definition, not by measurement. It's the same physical quantity written using power and current as its building blocks instead of the volt's own name.