Convert Milliamperes to CGS e.s. units
Milliampere (mA) to CGS e.s. unit (CGS e.s.) electric current conversion — enter any value below to get an instant result, or use the table for common values.
Results from this calculator are estimates provided for general informational purposes only, based on formulas, rates, and standards commonly accepted as of 2026. Figures may differ slightly from other calculators or professional sources due to rounding methods, differing assumptions, or regional regulations, and rules may change over time. Always consult a qualified professional — such as a financial advisor, healthcare provider, or other relevant specialist — before making decisions based on these results.
Result
1 mA = 2997924.5 CGS e.s.
1 Milliampere = 2997924.5 CGS e.s. units
1 CGS e.s. unit = 3.33564E-07 Milliamperes
1 mA in every supported unit
Conversion chart: Milliampere to CGS e.s. units
Conversion table
| Milliampere (mA) | CGS e.s. unit (CGS e.s.) |
|---|---|
| 0.01 mA | 29979.245 CGS e.s. |
| 0.1 mA | 299792.45 CGS e.s. |
| 1 mA | 2997924.5 CGS e.s. |
| 2 mA | 5995849.1 CGS e.s. |
| 3 mA | 8993773.6 CGS e.s. |
| 5 mA | 14989623 CGS e.s. |
| 10 mA | 29979245 CGS e.s. |
| 20 mA | 59958491 CGS e.s. |
| 50 mA | 1.4989623E+08 CGS e.s. |
| 100 mA | 2.9979245E+08 CGS e.s. |
| 1000 mA | 2.99792E+09 CGS e.s. |
Milliampere (mA)
Definition: The SI submultiple equal to one-thousandth of an ampere, giving electronics engineers a conveniently sized unit for the small currents typical of circuits and components.
History: Adopted alongside the rise of electronics and instrumentation, where currents in the ampere range were rare but currents in the thousandths of an ampere were the everyday norm — from early telegraph and telephone circuits through vacuum-tube electronics to modern integrated circuits.
Current use: The standard unit for battery capacity ratings (milliamp-hours, mAh), small electronic circuit and sensor currents, LED driver currents, and the current draw of low-power microcontrollers and IoT devices.
CGS e.s. unit (CGS e.s.)
Definition: The formal "CGS electrostatic unit" designation for current, another name for the statampere, equal to roughly 3.336×10⁻¹⁰ amperes.
History: The electrostatic-branch counterpart to the CGS e.m. unit designation, used in the same classic unit tables to distinguish electrostatic-system current quantities from their electromagnetic-system equivalents.
Current use: Essentially obsolete outside of historical reference tables; retained here for converting older scientific literature into modern SI current values.
Supported Units
| Unit | Symbol | In Ampere |
|---|---|---|
| Ampere | A | 1 A |
| Kiloampere | kA | 1000 A |
| Milliampere | mA | 0.001 A |
| Biot | Bi | 10 A |
| Abampere | abA | 10 A |
| EMU of Current | EMU | 10 A |
| Statampere | stA | 3.33564E-10 A |
| ESU of Current | ESU | 3.33564E-10 A |
| CGS e.m. unit | CGS e.m. | 10 A |
| CGS e.s. unit | CGS e.s. | 3.33564E-10 A |
About These Parameters
- Value
- The current value you want to convert, expressed in the "From" unit. Accepts decimals, and can represent anything from a microcontroller's milliampere-level draw to a lightning strike's kiloampere-scale peak current.
- From Unit
- The unit your input value is currently measured in — a modern device spec's ampere or milliampere rating, or a historical figure quoted in biots, abamperes, or another CGS-Gaussian current unit.
- To Unit
- The unit you want the result converted into. Use the swap button to flip From and To instantly, which is handy when translating an older CGS-based figure into the modern SI ampere or vice versa.
How Current Conversion Works
The Formula
Every unit here is defined by a fixed multiplier relative to the ampere. To convert a value from one unit to another:
result = value × (factor of "From" unit ÷ factor of "To" unit)
For Milliampere → CGS e.s. unit: multiply by 2997924.5. For example, 1 mA × 2997924.5 = 2997924.5 CGS e.s..
From CGS to SI
Before the SI system unified electromagnetic measurement, 19th-century physicists worked with two parallel centimeter-gram-second (CGS) unit families: the electromagnetic system (CGS-EMU), whose current unit was the abampere (also called the biot or "EMU of current"), and the electrostatic system (CGS-ESU), whose current unit was the statampere (also called "ESU of current"). The two families differ enormously in scale — one abampere equals 10 amperes, while one statampere equals only about 3.336×10⁻¹⁰ amperes — because they were built from Coulomb's law and Ampère's force law using different fundamental scaling assumptions, with the ratio between the two systems tracing back to the speed of light. The modern ampere, formally adopted in 1948 and redefined in 2019 via the elementary charge, replaced both CGS conventions with a single coherent, exactly reproducible standard.
Why So Many Names for the Same Value?
Biot, abampere, "EMU of current," and "CGS e.m. unit" are four different historical names that all refer to the exact same 10-ampere quantity, just coined in different contexts — Biot honors the physicist Jean-Baptiste Biot, "abampere" reflects the CGS-EMU "ab-" naming convention shared with abvolt and abohm, and "EMU of current" / "CGS e.m. unit" are the generic labels used in international unit tables to flag the electromagnetic-system current unit explicitly. The same pattern repeats on the electrostatic side with statampere, "ESU of current," and "CGS e.s. unit." Keeping all these historical names in one converter makes it possible to convert any older scientific paper's current figure — however it happens to be labeled — into a modern SI ampere value.
Example
A current of 1 mA equals 2997924.5 CGS e.s.. For scale, a typical USB port supplies around 0.5-3 amperes, a household circuit breaker might trip at 15-20 amperes, and a direct lightning strike can carry a peak current well over 30,000 amperes (30 kiloamperes) for a fraction of a second.
Frequently Asked Questions
How many CGS e.s. units are in 1 Milliampere?
1 Milliampere (mA) equals exactly 2997924.5 CGS e.s. units (CGS e.s.).
What is the difference between ampere and milliampere?
A milliampere is one-thousandth of an ampere (1 mA = 0.001 A). The ampere is the SI base unit used for everyday-scale currents like appliance draw or wiring capacity, while the milliampere is the practical unit for the much smaller currents typical of electronic circuits, sensors, and battery capacity ratings.
Are biot, abampere, and EMU of current really the same unit?
Yes — all three (plus "CGS e.m. unit") are different historical names for the identical CGS-electromagnetic current unit, equal to exactly 10 amperes. They arose from different naming conventions used in 19th- and early 20th-century physics literature rather than representing physically distinct quantities.
Why is the statampere such a tiny fraction of an ampere?
The statampere comes from the CGS electrostatic unit system, built directly from Coulomb's law without the ampere's scaling conventions. The huge size gap between it and the ampere — roughly a factor of 3×10⁹ — traces back to the speed of light, which relates the electrostatic and electromagnetic CGS unit families to each other.
How is the ampere defined today?
Since the 2019 redefinition of the SI, the ampere is defined by fixing the elementary charge at exactly 1.602176634×10⁻¹⁹ coulombs. One ampere is the current corresponding to a flow of exactly 1/(1.602176634×10⁻¹⁹) elementary charges per second — about 6.24×10¹⁸ charges per second — replacing the older force-between-parallel-wires definition used from 1948 to 2019.